IVAR IVARSAT-L-LE

IVARSAT-L-LE

Satellite module that independently manages low-temperature heating (mixed circuit) and instantaneous production of domestic hot water in each apartment when installed in district heating systems. Components: 30 plates heat exchanger; priority valve for domestic water circuit controlled by 230 V AC – 6 W motor; anti-scalding thermostatic mixing valve 36÷50 °C; anti-scalding device on domestic hot water circuit; thermometer on domestic hot water circuit; anti-pollution check valve at the inlet of domestic cold water circuit; mixing valve for fixed point mixing (with thermostatic control head and remote contact probe) or outside compensated temperature mixing (with axial servomotor and control unit); three-speed pump / model “E” with variable-speed pump EEI<20; summer/winter two-way valve; pocket for temperature immersion probe on delivery side of primary circuit; balancing valve on primary circuit; balancing by-pass valve on mixed circuit; balancing lockshield of heating/domestic water circuit; hydraulic separator with built-in check valve; shut-off ball valve; manual air vent valve; fill-drain valves; protection filter for heat meter; expanded polypropylene insulating shell; multifunctional electronic board. Circuit connections: 3/4” flat seal. Indicative power (to be verified according to the conditions of use): 10 kW heating side, 32 kW domestic water side. Production of 12 l/min of 48°C domestic water. Model “1” with high-temperature domestic water outlet. Model “R” with hot domestic water recirculation circuit complete with pump, check valve and electronic temperature sensor for domestic hot water priority mode activation. Installation: on frame, “C” in wall fitted box made of galvanized sheet-metal cover (white painted) 860-960 × 700 × 110-160 mm, “M” in wall hanging box made of aluminium (white painted) 722 × 600 × 150 mm. Optional accessories: mechanical or ultrasonic heat meter 1,5 o 2,5 m3/h, cold domestic water flow meter 1,5 m3/h, thermoelectric actuator, thermostatic control head, axial servomotor.

IVAR

IVARSAT-L-LE

Satellite module that independently manages low-temperature heating (mixed circuit) and instantaneous production of domestic hot water in each apartment when installed in district heating systems. Components: 30 plates heat exchanger; priority valve for domestic water circuit controlled by 230 V AC – 6 W motor; anti-scalding thermostatic mixing valve 36÷50 °C; anti-scalding device on domestic hot water circuit; thermometer on domestic hot water circuit; anti-pollution check valve at the inlet of domestic cold water circuit; mixing valve for fixed point mixing (with thermostatic control head and remote contact probe) or outside compensated temperature mixing (with axial servomotor and control unit); three-speed pump / model “E” with variable-speed pump EEI<20; summer/winter two-way valve; pocket for temperature immersion probe on delivery side of primary circuit; balancing valve on primary circuit; balancing by-pass valve on mixed circuit; balancing lockshield of heating/domestic water circuit; hydraulic separator with built-in check valve; shut-off ball valve; manual air vent valve; fill-drain valves; protection filter for heat meter; expanded polypropylene insulating shell; multifunctional electronic board. Circuit connections: 3/4” flat seal. Indicative power (to be verified according to the conditions of use): 10 kW heating side, 32 kW domestic water side. Production of 12 l/min of 48°C domestic water. Model “1” with high-temperature domestic water outlet. Model “R” with hot domestic water recirculation circuit complete with pump, check valve and electronic temperature sensor for domestic hot water priority mode activation. Installation: on frame, “C” in wall fitted box made of galvanized sheet-metal cover (white painted) 860-960 × 700 × 110-160 mm, “M” in wall hanging box made of aluminium (white painted) 722 × 600 × 150 mm. Optional accessories: mechanical or ultrasonic heat meter 1,5 o 2,5 m3/h, cold domestic water flow meter 1,5 m3/h, thermoelectric actuator, thermostatic control head, axial servomotor.

Conform cu EMCS

.RFA

Distribuitoare - Termice

IVAR

Descărcare
IVAR IVARSAT-HL-HLE

IVARSAT-HL-HLE

Satellite module that independently manages high-temperature and low-temperature heating (direct and mixed circuits) and instantaneous production of domestic hot water in each apartment when installed in district heating systems. Components: 30 plates heat exchanger; priority valve for domestic water circuit controlled by 230 V AC – 6 W motor; anti-scalding thermostatic mixing valve 36÷50 °C; anti-scalding device on domestic hot water circuit; thermometer on domestic hot water circuit; anti-pollution check valve at the inlet of domestic cold water circuit; mixing valve for fixed point mixing (with thermostatic control head and remote contact probe) or outside compensated temperature mixing (with axial servomotor and control unit); three-speed pump / model “E” with variable-speed pump EEI<20; summer/winter two-way valve on high-temperature and low-temperature circuits; pocket for temperature immersion probe on delivery side of primary circuit; balancing valve on primary circuit; balancing by-pass valve on mixed circuit; balancing lockshield of heating/domestic water circuit; hydraulic separator with built-in check valve; shut-off ball valve; manual air vent valve; fill-drain valves; protection filter for heat meter; expanded polypropylene insulating shell; multifunctional electronic board. Circuit connections: 3/4” flat seal. Indicative power (to be verified according to the conditions of use): 10 kW heating side, 32 kW domestic water side. Production of 12 l/min of 48°C domestic water. High-temperature domestic water outlet. Hot domestic water recirculation circuit complete with pump, check valve and electronic temperature sensor for domestic hot water priority mode activation. Installation: on frame, “C” in wall fitted box made of galvanized sheet-metal cover (white painted) 860-960 × 700 × 110-160 mm, “M” in wall hanging box made of aluminium (white painted) 722 × 600 × 150 mm. Optional accessories: mechanical or ultrasonic heat meter 1,5 o 2,5 m3/h, cold domestic water flow meter 1,5 m3/h, thermoelectric actuator, thermostatic control head, axial servomotor.

IVAR

IVARSAT-HL-HLE

Satellite module that independently manages high-temperature and low-temperature heating (direct and mixed circuits) and instantaneous production of domestic hot water in each apartment when installed in district heating systems. Components: 30 plates heat exchanger; priority valve for domestic water circuit controlled by 230 V AC – 6 W motor; anti-scalding thermostatic mixing valve 36÷50 °C; anti-scalding device on domestic hot water circuit; thermometer on domestic hot water circuit; anti-pollution check valve at the inlet of domestic cold water circuit; mixing valve for fixed point mixing (with thermostatic control head and remote contact probe) or outside compensated temperature mixing (with axial servomotor and control unit); three-speed pump / model “E” with variable-speed pump EEI<20; summer/winter two-way valve on high-temperature and low-temperature circuits; pocket for temperature immersion probe on delivery side of primary circuit; balancing valve on primary circuit; balancing by-pass valve on mixed circuit; balancing lockshield of heating/domestic water circuit; hydraulic separator with built-in check valve; shut-off ball valve; manual air vent valve; fill-drain valves; protection filter for heat meter; expanded polypropylene insulating shell; multifunctional electronic board. Circuit connections: 3/4” flat seal. Indicative power (to be verified according to the conditions of use): 10 kW heating side, 32 kW domestic water side. Production of 12 l/min of 48°C domestic water. High-temperature domestic water outlet. Hot domestic water recirculation circuit complete with pump, check valve and electronic temperature sensor for domestic hot water priority mode activation. Installation: on frame, “C” in wall fitted box made of galvanized sheet-metal cover (white painted) 860-960 × 700 × 110-160 mm, “M” in wall hanging box made of aluminium (white painted) 722 × 600 × 150 mm. Optional accessories: mechanical or ultrasonic heat meter 1,5 o 2,5 m3/h, cold domestic water flow meter 1,5 m3/h, thermoelectric actuator, thermostatic control head, axial servomotor.

Conform cu EMCS

.RFA

Distribuitoare - Termice

IVAR

Descărcare
IVAR IVARSAT-H

IVARSAT-H

Satellite module that independently manages high-temperature heating (direct circuit) and instantaneous production of domestic hot water in each apartment when installed in district heating systems. Components: 30 plates heat exchanger; priority valve for domestic water circuit controlled by 230 V AC – 6 W motor; anti-scalding thermostatic mixing valve 36÷50 °C; domestic water preheating device; anti-scalding device on domestic hot water circuit; thermometer on domestic hot water circuit; anti-pollution check valve at the inlet of domestic cold water circuit; summer/winter two-way valve; pocket for temperature immersion probe on delivery side of primary circuit; balancing lockshield of primary circuit with double micrometrical adjustment; balancing lockshield of heating/domestic water circuit; differential overpressure by-pass valve on primary circuit; shut-off ball valve; manual air vent valve; fill-drain valves; protection filter for heat meter; expanded polypropylene insulating shell; multifunctional electronic board. Circuit connections: 3/4” flat seal. Indicative power (to be verified according to the conditions of use): 10 kW heating side, 32 kW domestic water side. Production of 12 l/min of 48°C domestic water. Model “1” with high-temperature domestic water outlet. Model “R” with hot domestic water recirculation circuit complete with pump, check valve and electronic temperature sensor for domestic hot water priority mode activation. Installation: on frame, “C” in wall fitted box made of galvanized sheet-metal cover (white painted) 860-960 × 700 × 110-160 mm, “M” in wall hanging box made of aluminium (white painted) 722 × 600 × 150 mm. Optional accessories: mechanical or ultrasonic heat meter 1,5 o 2,5 m3/h, cold domestic water flow meter 1,5 m3/h, thermoelectric actuator, thermostatic control head, axial servomotor.

IVAR

IVARSAT-H

Satellite module that independently manages high-temperature heating (direct circuit) and instantaneous production of domestic hot water in each apartment when installed in district heating systems. Components: 30 plates heat exchanger; priority valve for domestic water circuit controlled by 230 V AC – 6 W motor; anti-scalding thermostatic mixing valve 36÷50 °C; domestic water preheating device; anti-scalding device on domestic hot water circuit; thermometer on domestic hot water circuit; anti-pollution check valve at the inlet of domestic cold water circuit; summer/winter two-way valve; pocket for temperature immersion probe on delivery side of primary circuit; balancing lockshield of primary circuit with double micrometrical adjustment; balancing lockshield of heating/domestic water circuit; differential overpressure by-pass valve on primary circuit; shut-off ball valve; manual air vent valve; fill-drain valves; protection filter for heat meter; expanded polypropylene insulating shell; multifunctional electronic board. Circuit connections: 3/4” flat seal. Indicative power (to be verified according to the conditions of use): 10 kW heating side, 32 kW domestic water side. Production of 12 l/min of 48°C domestic water. Model “1” with high-temperature domestic water outlet. Model “R” with hot domestic water recirculation circuit complete with pump, check valve and electronic temperature sensor for domestic hot water priority mode activation. Installation: on frame, “C” in wall fitted box made of galvanized sheet-metal cover (white painted) 860-960 × 700 × 110-160 mm, “M” in wall hanging box made of aluminium (white painted) 722 × 600 × 150 mm. Optional accessories: mechanical or ultrasonic heat meter 1,5 o 2,5 m3/h, cold domestic water flow meter 1,5 m3/h, thermoelectric actuator, thermostatic control head, axial servomotor.

Conform cu EMCS

.RFA

Distribuitoare - Termice

IVAR

Descărcare
IVAR IVARSAT-H VNR

IVARSAT-H VNR

Satellite module that independently manages high-temperature heating (direct circuit) and instantaneous production of domestic hot water in each apartment when installed in district heating systems. Components: 30 plates heat exchanger; priority valve for domestic water circuit controlled by 230 V AC – 6 W motor; anti-scalding thermostatic mixing valve 36÷50 °C; domestic water preheating device; anti-scalding device on domestic hot water circuit; thermometer on domestic hot water circuit; anti-pollution check valve at the inlet of domestic cold water circuit; summer/winter two-way valve; pocket for temperature immersion probe on delivery side of primary circuit; balancing lockshield of primary circuit with double micrometrical adjustment; balancing lockshield of heating/domestic water circuit; differential overpressure by-pass valve on primary circuit; shut-off ball valve; manual air vent valve; fill-drain valves; protection filter for heat meter; expanded polypropylene insulating shell; multifunctional electronic board. Circuit connections: 3/4” flat seal. Indicative power (to be verified according to the conditions of use): 10 kW heating side, 32 kW domestic water side. Production of 12 l/min of 48°C domestic water. Model “1” with high-temperature domestic water outlet. Model “R” with hot domestic water recirculation circuit complete with pump, check valve and electronic temperature sensor for domestic hot water priority mode activation. Installation: on frame, “C” in wall fitted box made of galvanized sheet-metal cover (white painted) 860-960 × 700 × 110-160 mm, “M” in wall hanging box made of aluminium (white painted) 722 × 600 × 150 mm. Optional accessories: mechanical or ultrasonic heat meter 1,5 o 2,5 m3/h, cold domestic water flow meter 1,5 m3/h, thermoelectric actuator, thermostatic control head, axial servomotor. In compliance with Belgaqua.

IVAR

IVARSAT-H VNR

Satellite module that independently manages high-temperature heating (direct circuit) and instantaneous production of domestic hot water in each apartment when installed in district heating systems. Components: 30 plates heat exchanger; priority valve for domestic water circuit controlled by 230 V AC – 6 W motor; anti-scalding thermostatic mixing valve 36÷50 °C; domestic water preheating device; anti-scalding device on domestic hot water circuit; thermometer on domestic hot water circuit; anti-pollution check valve at the inlet of domestic cold water circuit; summer/winter two-way valve; pocket for temperature immersion probe on delivery side of primary circuit; balancing lockshield of primary circuit with double micrometrical adjustment; balancing lockshield of heating/domestic water circuit; differential overpressure by-pass valve on primary circuit; shut-off ball valve; manual air vent valve; fill-drain valves; protection filter for heat meter; expanded polypropylene insulating shell; multifunctional electronic board. Circuit connections: 3/4” flat seal. Indicative power (to be verified according to the conditions of use): 10 kW heating side, 32 kW domestic water side. Production of 12 l/min of 48°C domestic water. Model “1” with high-temperature domestic water outlet. Model “R” with hot domestic water recirculation circuit complete with pump, check valve and electronic temperature sensor for domestic hot water priority mode activation. Installation: on frame, “C” in wall fitted box made of galvanized sheet-metal cover (white painted) 860-960 × 700 × 110-160 mm, “M” in wall hanging box made of aluminium (white painted) 722 × 600 × 150 mm. Optional accessories: mechanical or ultrasonic heat meter 1,5 o 2,5 m3/h, cold domestic water flow meter 1,5 m3/h, thermoelectric actuator, thermostatic control head, axial servomotor. In compliance with Belgaqua.

Conform cu EMCS

.RFA

Distribuitoare - Termice

IVAR

Descărcare
Mitsubishi Electric Ecodan PAC-MK52-53BC

Ecodan PAC-MK52-53BC

BC controllers Place directly in Revit and AutoCAD using the free [a href="https://store.mepcontent.com/Product/Details/49" target="_blank"]Mitsubishi Electric System Designer[/a] App

Mitsubishi Electric

Ecodan PAC-MK52-53BC

BC controllers Place directly in Revit and AutoCAD using the free [a href="https://store.mepcontent.com/Product/Details/49" target="_blank"]Mitsubishi Electric System Designer[/a] App

Conform cu EMCS

.DWG .RFA .IFC

Distribuitoare - Termice

Mitsubishi Electric

Descărcare
Mitsubishi Electric Ecodan PAC-MK32-33BC

Ecodan PAC-MK32-33BC

BC controllers Place directly in Revit and AutoCAD using the free [a href="https://store.mepcontent.com/Product/Details/49" target="_blank"]Mitsubishi Electric System Designer[/a] App

Mitsubishi Electric

Ecodan PAC-MK32-33BC

BC controllers Place directly in Revit and AutoCAD using the free [a href="https://store.mepcontent.com/Product/Details/49" target="_blank"]Mitsubishi Electric System Designer[/a] App

Conform cu EMCS

.DWG .RFA .IFC

Distribuitoare - Termice

Mitsubishi Electric

Descărcare
IVAR BRASS-ROD MANIFOLDS_CI554MN

BRASS-ROD MANIFOLDS_CI554MN

Return manifold with manually operated isolation valves and EUROK connections. Manifolds can be used as return manifolds only. The body is made of brass CW617N. Nickel-plated outer finished or yellow outer finished. Gaskets and O-rings: Peroxide EPDM. Maximum fluid temperature: 120°C. Maximum operating pressure: 10 bar.  Main connections: G 1"F or G 1"1/4F. Secondary connections: EUROK. Sizes available: from 1 to 13 ways.

IVAR

BRASS-ROD MANIFOLDS_CI554MN

Return manifold with manually operated isolation valves and EUROK connections. Manifolds can be used as return manifolds only. The body is made of brass CW617N. Nickel-plated outer finished or yellow outer finished. Gaskets and O-rings: Peroxide EPDM. Maximum fluid temperature: 120°C. Maximum operating pressure: 10 bar.  Main connections: G 1"F or G 1"1/4F. Secondary connections: EUROK. Sizes available: from 1 to 13 ways.

Conform cu EMCS

.RFA

Distribuitoare - Termice

IVAR

Descărcare
IVAR BRASS-ROD MANIFOLDS_CI562MN

BRASS-ROD MANIFOLDS_CI562MN

Kit made of flow manifold with double micrometric adjustment lockshields, return manifold with manually operated isolation valves, brackets and EUROK connections. The body is made of brass CW617N. Nickel-plated outer finished or yellow outer finished. Gaskets and O-rings: Peroxide EPDM. Maximum fluid temperature: 120°C. Maximum operating pressure: 10 bar. Main connections: G 1"F or G 1"1/4F. Secondary connections: EUROK. Sizes available: from 2 to 13 ways.

IVAR

BRASS-ROD MANIFOLDS_CI562MN

Kit made of flow manifold with double micrometric adjustment lockshields, return manifold with manually operated isolation valves, brackets and EUROK connections. The body is made of brass CW617N. Nickel-plated outer finished or yellow outer finished. Gaskets and O-rings: Peroxide EPDM. Maximum fluid temperature: 120°C. Maximum operating pressure: 10 bar. Main connections: G 1"F or G 1"1/4F. Secondary connections: EUROK. Sizes available: from 2 to 13 ways.

Conform cu EMCS

.RFA

Distribuitoare - Termice

IVAR

Descărcare
IVAR BRASS-ROD MANIFOLDS_CI595MN

BRASS-ROD MANIFOLDS_CI595MN

Kit made of flow manifold with flow meter/adjusters FLUXER (0-5 l/min), return manifold with manually operated isolation valves, brackets and EUROK connections. The body is made of brass CW617N. Nickel-plated outer finished or yellow outer finished. Gaskets and O-rings: Peroxide EPDM. Maximum fluid temperature: 90°C. Maximum operating pressure: 10 bar. Main connections: G 1"F or G 1"1/4F. Secondary connections: EUROK. Sizes available: from 2 to 13 ways.

IVAR

BRASS-ROD MANIFOLDS_CI595MN

Kit made of flow manifold with flow meter/adjusters FLUXER (0-5 l/min), return manifold with manually operated isolation valves, brackets and EUROK connections. The body is made of brass CW617N. Nickel-plated outer finished or yellow outer finished. Gaskets and O-rings: Peroxide EPDM. Maximum fluid temperature: 90°C. Maximum operating pressure: 10 bar. Main connections: G 1"F or G 1"1/4F. Secondary connections: EUROK. Sizes available: from 2 to 13 ways.

Conform cu EMCS

.RFA

Distribuitoare - Termice

IVAR

Descărcare
IVAR BRASS-ROD MANIFOLDS_CI600N

BRASS-ROD MANIFOLDS_CI600N

Flow manifold with flow meter/adjuster FLUXER (0-5 l/min) and EUROK connections. Manifolds can be used as supply manifolds only. The body is made of brass CW617N. Nickel-plated outer finished or yellow outer finished. Gaskets and O-rings: Peroxide EPDM. Maximum fluid temperature: 90°C. Maximum operating pressure: 10 bar.  Main connections: G 1"F or G 1"1/4F. Secondary connections: EUROK. Sizes available: from 1 to 13 ways.

IVAR

BRASS-ROD MANIFOLDS_CI600N

Flow manifold with flow meter/adjuster FLUXER (0-5 l/min) and EUROK connections. Manifolds can be used as supply manifolds only. The body is made of brass CW617N. Nickel-plated outer finished or yellow outer finished. Gaskets and O-rings: Peroxide EPDM. Maximum fluid temperature: 90°C. Maximum operating pressure: 10 bar.  Main connections: G 1"F or G 1"1/4F. Secondary connections: EUROK. Sizes available: from 1 to 13 ways.

Conform cu EMCS

.RFA

Distribuitoare - Termice

IVAR

Descărcare
IVAR BRASS-ROD MANIFOLDS_CS502N

BRASS-ROD MANIFOLDS_CS502N

Plain manifold with EUROK connections. Manifolds can be used as supply or return manifolds. The body is made of brass CW617N. Nickel-plated outer finished or yellow outer finished. Gaskets and O-rings: Peroxide EPDM. Maximum fluid temperature: 120°C. Maximum operating pressure: 10 bar. Main connections: G 3/4"F or G 1"F or G 1"1/4F. Secondary connections: EUROK. Sizes available: from 2 to 13 ways.

IVAR

BRASS-ROD MANIFOLDS_CS502N

Plain manifold with EUROK connections. Manifolds can be used as supply or return manifolds. The body is made of brass CW617N. Nickel-plated outer finished or yellow outer finished. Gaskets and O-rings: Peroxide EPDM. Maximum fluid temperature: 120°C. Maximum operating pressure: 10 bar. Main connections: G 3/4"F or G 1"F or G 1"1/4F. Secondary connections: EUROK. Sizes available: from 2 to 13 ways.

Conform cu EMCS

.RFA

Distribuitoare - Termice

IVAR

Descărcare
IVAR BRASS-ROD MANIFOLDS_KC01KC

BRASS-ROD MANIFOLDS_KC01KC

Kit made of flow manifold with double micrometric adjustment lockshields, return manifold with manually operated isolation valves, brackets, terminals, filling/drainage valves, air vent valves and EUROK connections. The body is made of brass CW617N. Nickel-plated outer finished or yellow outer finished.  Gaskets and O-rings: Peroxide EPDM. Maximum fluid temperature: 120°C. Maximum operating pressure: 10 bar. Main connections: G 1"F or G 1"1/4F. Secondary connections: EUROK. Sizes available: from 2 to 13 ways.

IVAR

BRASS-ROD MANIFOLDS_KC01KC

Kit made of flow manifold with double micrometric adjustment lockshields, return manifold with manually operated isolation valves, brackets, terminals, filling/drainage valves, air vent valves and EUROK connections. The body is made of brass CW617N. Nickel-plated outer finished or yellow outer finished.  Gaskets and O-rings: Peroxide EPDM. Maximum fluid temperature: 120°C. Maximum operating pressure: 10 bar. Main connections: G 1"F or G 1"1/4F. Secondary connections: EUROK. Sizes available: from 2 to 13 ways.

Conform cu EMCS

.RFA

Distribuitoare - Termice

IVAR

Descărcare
IVAR BRASS-ROD MANIFOLDS KC02KC

BRASS-ROD MANIFOLDS KC02KC

Kit made of flow manifold with flow meters/adjusters FLUXER (0-5 l/min), return manifold with manually operated isolation valves, brackets, terminals, filling/drainage valves, air vent valves and EUROK connections. The body is made of brass CW617N. Nickel-plated outer finished or yellow outer finished.  Gaskets and O-rings: Peroxide EPDM. Maximum fluid temperature: 120°C. Maximum operating pressure: 10 bar.  Main connections: G 1"F or G 1"1/4F. Secondary connections: EUROK. Sizes available: from 2 to 13 ways.

IVAR

BRASS-ROD MANIFOLDS KC02KC

Kit made of flow manifold with flow meters/adjusters FLUXER (0-5 l/min), return manifold with manually operated isolation valves, brackets, terminals, filling/drainage valves, air vent valves and EUROK connections. The body is made of brass CW617N. Nickel-plated outer finished or yellow outer finished.  Gaskets and O-rings: Peroxide EPDM. Maximum fluid temperature: 120°C. Maximum operating pressure: 10 bar.  Main connections: G 1"F or G 1"1/4F. Secondary connections: EUROK. Sizes available: from 2 to 13 ways.

Conform cu EMCS

.RFA

Distribuitoare - Termice

IVAR

Descărcare
IVAR BRASS-ROD MANIFOLDS_CI552N

BRASS-ROD MANIFOLDS_CI552N

Flow manifold with micrometric dually adjusted lockshields and EUROK connections. Manifolds can be used as supply manifolds only. The body is made of brass CW617N. Nickel-plated outer finished or yellow outer finished. Gaskets and O-rings: Peroxide EPDM. Maximum fluid temperature: 120°C.Maximum operating pressure: 10 bar.  Main connections: G 1"F or G 1"1/4F. Secondary connections: EUROK. Sizes available: from 1 to 13 ways.

IVAR

BRASS-ROD MANIFOLDS_CI552N

Flow manifold with micrometric dually adjusted lockshields and EUROK connections. Manifolds can be used as supply manifolds only. The body is made of brass CW617N. Nickel-plated outer finished or yellow outer finished. Gaskets and O-rings: Peroxide EPDM. Maximum fluid temperature: 120°C.Maximum operating pressure: 10 bar.  Main connections: G 1"F or G 1"1/4F. Secondary connections: EUROK. Sizes available: from 1 to 13 ways.

Conform cu EMCS

.RFA

Distribuitoare - Termice

IVAR

Descărcare
IVAR IVARSAT-H

IVARSAT-H

The satellite module IvarSAT-H independently manages high-temperature heating (direct circuit) in centralized systems and instantaneous production of domestic hot water in each apartment. Optional equipment: “R” with recirculation circuit complete with pump, “1” with high-temperature domestic water outlet. Mode of installation: on frame, “C” in wall fitted box made of galvanized sheet-metal cover painted white 860-960×700×110-160 mm, “M” in wall hanging box made of aluminium painted white 722×600×150 mm. Optional accessories: heat meter, flow meter, electrothermal head, thermostatic head, axial motor.

IVAR

IVARSAT-H

The satellite module IvarSAT-H independently manages high-temperature heating (direct circuit) in centralized systems and instantaneous production of domestic hot water in each apartment. Optional equipment: “R” with recirculation circuit complete with pump, “1” with high-temperature domestic water outlet. Mode of installation: on frame, “C” in wall fitted box made of galvanized sheet-metal cover painted white 860-960×700×110-160 mm, “M” in wall hanging box made of aluminium painted white 722×600×150 mm. Optional accessories: heat meter, flow meter, electrothermal head, thermostatic head, axial motor.

Conform cu EMCS

.RFA

Distribuitoare - Termice

IVAR

Descărcare
Remeha Connection Sets 310/610 Eco Pro

Connection Sets 310/610 Eco Pro

Connector sets from Remeha

Remeha

Connection Sets 310/610 Eco Pro

Connector sets from Remeha

Conform cu EMCS

.DWG .RFA .IFC

Distribuitoare - Termice

Remeha

Descărcare
Albrand Boxer CF

Boxer CF

Distributor Boxer CF

Albrand

Boxer CF

Distributor Boxer CF

Conform cu EMCS

.RFA

Distribuitoare - Termice

Albrand

Descărcare
Albrand Boxer FL

Boxer FL

Distributor Boxer FL

Albrand

Boxer FL

Distributor Boxer FL

Conform cu EMCS

.RFA

Distribuitoare - Termice

Albrand

Descărcare
Albrand Boxer ST

Boxer ST

Distributor Boxer ST

Albrand

Boxer ST

Distributor Boxer ST

Conform cu EMCS

.RFA

Distribuitoare - Termice

Albrand

Descărcare
Albrand Boxer VV

Boxer VV

Distributor Boxer VV

Albrand

Boxer VV

Distributor Boxer VV

Conform cu EMCS

.RFA

Distribuitoare - Termice

Albrand

Descărcare
Albrand Messing CF

Messing CF

Distributor Messing CF

Albrand

Messing CF

Distributor Messing CF

Conform cu EMCS

.RFA

Distribuitoare - Termice

Albrand

Descărcare
Albrand Messing FL

Messing FL

Distributor Messing FL

Albrand

Messing FL

Distributor Messing FL

Conform cu EMCS

.RFA

Distribuitoare - Termice

Albrand

Descărcare
IVAR IVARPRESS – PRESS FITTINGS – Line

IVARPRESS – PRESS FITTINGS – Line

IVARPRESS is an IVAR press fitting studied and tested to be used with B crimper profile. The geometry of the fitting, designed for ideal coupling between pipe and fitting ensuing pressing, and the windows on the bushing holder, to verify correct insertion of the pipe and two O-rings in peroxide EPDM on each terminal, are all details which help to guarantee the usability and reliability of the product. The body is made of CW617N nickel-finished brass on the outer surface and yellow for all other parts in contact with fluid in conformity with the latest standards-regulations for drinking water plant. Available in a wide range of configurations and sizes.

IVAR

IVARPRESS – PRESS FITTINGS – Line

IVARPRESS is an IVAR press fitting studied and tested to be used with B crimper profile. The geometry of the fitting, designed for ideal coupling between pipe and fitting ensuing pressing, and the windows on the bushing holder, to verify correct insertion of the pipe and two O-rings in peroxide EPDM on each terminal, are all details which help to guarantee the usability and reliability of the product. The body is made of CW617N nickel-finished brass on the outer surface and yellow for all other parts in contact with fluid in conformity with the latest standards-regulations for drinking water plant. Available in a wide range of configurations and sizes.

Conform cu EMCS

.RVT .PDF

Distribuitoare - Termice

IVAR

Descărcare
IVAR MPLC MULTI PRESS WITH LEAKAGE FUNCTION CUPHIN - Line

MPLC MULTI PRESS WITH LEAKAGE FUNCTION CUPHIN - Line

MULTI•PRESS•LEAK•CUPHIN is the new press fitting designed to guarantee water leakage in case of failed pressing and to be used indifferently with 7 different crimper profiles (BE, B, TH, R, H, F, U). The absence of sealing if not pressed is a function which is especially on demand on the market to avoid problems and damage in case of forgotten pressing: thanks to the system test, the installer can immediately identify leaks and repair them by correctly pressing the fitting. Available in a wide range of configurations and sizes. Fitting body made of Cuphin CW724R.

IVAR

MPLC MULTI PRESS WITH LEAKAGE FUNCTION CUPHIN - Line

MULTI•PRESS•LEAK•CUPHIN is the new press fitting designed to guarantee water leakage in case of failed pressing and to be used indifferently with 7 different crimper profiles (BE, B, TH, R, H, F, U). The absence of sealing if not pressed is a function which is especially on demand on the market to avoid problems and damage in case of forgotten pressing: thanks to the system test, the installer can immediately identify leaks and repair them by correctly pressing the fitting. Available in a wide range of configurations and sizes. Fitting body made of Cuphin CW724R.

Conform cu EMCS

.RVT .PDF

Distribuitoare - Termice

IVAR

Descărcare
IVAR MPL PRESS FITTINGS WITH LEAKAGE FUNCTION – Line

MPL PRESS FITTINGS WITH LEAKAGE FUNCTION – Line

MULTI•PRESS•LEAK is the new press fitting designed to guarantee water leakage in case of failed pressing and to be used indifferently with 7 different crimper profiles (BE, B, TH, R, H, F, U). The absence of sealing if not pressed is a function which is especially on demand on the market to avoid problems and damage in case of forgotten pressing: thanks to the system test, the installer can immediately identify leaks and repair them by correctly pressing the fitting. Available in a wide range of configurations and sizes.

IVAR

MPL PRESS FITTINGS WITH LEAKAGE FUNCTION – Line

MULTI•PRESS•LEAK is the new press fitting designed to guarantee water leakage in case of failed pressing and to be used indifferently with 7 different crimper profiles (BE, B, TH, R, H, F, U). The absence of sealing if not pressed is a function which is especially on demand on the market to avoid problems and damage in case of forgotten pressing: thanks to the system test, the installer can immediately identify leaks and repair them by correctly pressing the fitting. Available in a wide range of configurations and sizes.

Conform cu EMCS

.RVT .PDF

Distribuitoare - Termice

IVAR

Descărcare
IVAR MP PRESS FITTINGS - Line

MP PRESS FITTINGS - Line

MULTI•PRESS is an IVAR press fitting studied and tested to be used indifferently with 7 different crimper profiles (BE, B, TH, R, H, F, U). The geometry of the fitting, designed for ideal coupling between pipe and fitting ensuing pressing, and the windows on the bushing holder, to verify correct insertion of the pipe and two O-rings in peroxide EPDM on each terminal, are all details which help to guarantee the usability and reliability of the product. Available in a wide range of configurations and sizes.

IVAR

MP PRESS FITTINGS - Line

MULTI•PRESS is an IVAR press fitting studied and tested to be used indifferently with 7 different crimper profiles (BE, B, TH, R, H, F, U). The geometry of the fitting, designed for ideal coupling between pipe and fitting ensuing pressing, and the windows on the bushing holder, to verify correct insertion of the pipe and two O-rings in peroxide EPDM on each terminal, are all details which help to guarantee the usability and reliability of the product. Available in a wide range of configurations and sizes.

Conform cu EMCS

.RVT .PDF

Distribuitoare - Termice

IVAR

Descărcare
IVAR IVAR ESAT DUAL

IVAR ESAT DUAL

IVAR E-SAT DUAL is a double heat exchanger satellite module which allows on-site production of DHW and hot water for the heating system, with only AFS connections and technical water supply/return. Thanks to the integrated electronics IVAR E-SAT modulates the technical water flow to guarantee a low return temperature to the boiler. The double exchanger solution, completely separating the centralized system from the domestic one, guarantees easy maintenance of the single user system. IVAR ESAT DUAL can be equipped with differential pressure valves and shut-off valves kit.

IVAR

IVAR ESAT DUAL

IVAR E-SAT DUAL is a double heat exchanger satellite module which allows on-site production of DHW and hot water for the heating system, with only AFS connections and technical water supply/return. Thanks to the integrated electronics IVAR E-SAT modulates the technical water flow to guarantee a low return temperature to the boiler. The double exchanger solution, completely separating the centralized system from the domestic one, guarantees easy maintenance of the single user system. IVAR ESAT DUAL can be equipped with differential pressure valves and shut-off valves kit.

Conform cu EMCS

.RFA .PDF

Distribuitoare - Termice

IVAR

Descărcare
IVAR IS-BOX

IS-BOX

IS-BOX is a box with a pair of pre-installed 3+1 and 4+1 outlet sanitary manifolds, suitable for wall recessing even in bathrooms covered with tiles or valuable materials. The reduced size allows it to be installed in brick or plasterboard walls with a minimum thickness of 60 mm. The manifolds are compatible with drinking water and the inlets can be shut off by screw sealing valves and replaceable headworks. Available in two colours (white and chrome), also in the completely inspectable version.

IVAR

IS-BOX

IS-BOX is a box with a pair of pre-installed 3+1 and 4+1 outlet sanitary manifolds, suitable for wall recessing even in bathrooms covered with tiles or valuable materials. The reduced size allows it to be installed in brick or plasterboard walls with a minimum thickness of 60 mm. The manifolds are compatible with drinking water and the inlets can be shut off by screw sealing valves and replaceable headworks. Available in two colours (white and chrome), also in the completely inspectable version.

Conform cu EMCS

.RFA .PDF

Distribuitoare - Termice

IVAR

Descărcare
Mitsubishi Electric FAQ IMP Copper pipes Mitsubishi

FAQ IMP Copper pipes Mitsubishi

This manual describes how you can create a new pipe and add Imperial Diameters in Revit MEP. Place directly in Revit and AutoCAD using the free [a href="https://store.mepcontent.com/Product/Details/49" target="_blank"]Mitsubishi Electric System Designer[/a] App

Mitsubishi Electric

FAQ IMP Copper pipes Mitsubishi

This manual describes how you can create a new pipe and add Imperial Diameters in Revit MEP. Place directly in Revit and AutoCAD using the free [a href="https://store.mepcontent.com/Product/Details/49" target="_blank"]Mitsubishi Electric System Designer[/a] App

Conform cu EMCS

.PDF

Distribuitoare - Termice

Mitsubishi Electric

Descărcare
Mitsubishi Electric City Multi BC Controllers (Model 2018)

City Multi BC Controllers (Model 2018)

BC controller Place directly in Revit and AutoCAD using the free [a href="https://store.mepcontent.com/Product/Details/49" target="_blank"]Mitsubishi Electric System Designer[/a] App

Mitsubishi Electric

City Multi BC Controllers (Model 2018)

BC controller Place directly in Revit and AutoCAD using the free [a href="https://store.mepcontent.com/Product/Details/49" target="_blank"]Mitsubishi Electric System Designer[/a] App

Conform cu EMCS

.DWG .RFA .IFC

Distribuitoare - Termice

Mitsubishi Electric

Descărcare
Therminon Composite unit model District Heating Nuon

Composite unit model District Heating Nuon

1-16-GROUP COMP UNIT MODEL: NUON DISTRICT HEATING

Therminon

Composite unit model District Heating Nuon

1-16-GROUP COMP UNIT MODEL: NUON DISTRICT HEATING

Conform cu EMCS

.RFA

Distribuitoare - Termice

Therminon

Descărcare
Therminon Composite unit model District Heating Essent

Composite unit model District Heating Essent

1-16-GROUP COMP UNIT MODEL: ESSENT DISTRICT HEATING

Therminon

Composite unit model District Heating Essent

1-16-GROUP COMP UNIT MODEL: ESSENT DISTRICT HEATING

Conform cu EMCS

.RFA

Distribuitoare - Termice

Therminon

Descărcare
Therminon Composite unit model OEM LTV split system heating/cooling

Composite unit model OEM LTV split system heating/cooling

1-16-GROUP OEM LTV / FLOWMETERS + COMP. EUROCONE EASY-CONNECTORS + SPLIT SYSTEM HEAT EXCHANGER PACK 4-PIPE / 5.5 KVS THERM. VALVES / COOLING VALVE NC

Therminon

Composite unit model OEM LTV split system heating/cooling

1-16-GROUP OEM LTV / FLOWMETERS + COMP. EUROCONE EASY-CONNECTORS + SPLIT SYSTEM HEAT EXCHANGER PACK 4-PIPE / 5.5 KVS THERM. VALVES / COOLING VALVE NC

Conform cu EMCS

.RFA

Distribuitoare - Termice

Therminon

Descărcare
Therminon Composite unit model OEM LTV 4 pipes connection

Composite unit model OEM LTV 4 pipes connection

1-16-GR OEM LTV / FLOWMETERS + COMP. EUROCONE EASY-CONNECTORS + SET 4-PIPE CONN. 3/4'' + 4 X 5.5 KVS THERM. VALVES

Therminon

Composite unit model OEM LTV 4 pipes connection

1-16-GR OEM LTV / FLOWMETERS + COMP. EUROCONE EASY-CONNECTORS + SET 4-PIPE CONN. 3/4'' + 4 X 5.5 KVS THERM. VALVES

Conform cu EMCS

.RFA

Distribuitoare - Termice

Therminon

Descărcare
Therminon Composite unit model OEM LTV split system double heat exchanger

Composite unit model OEM LTV split system double heat exchanger

1-16-GROUP OEM LTV / FLOWMETERS + COMP. EUROCONE EASY-CONNECTORS + SPLIT SYSTEM / DOUBLE HEAT EXCHANGER PACK + 5.5 KVS THERM. VALVES

Therminon

Composite unit model OEM LTV split system double heat exchanger

1-16-GROUP OEM LTV / FLOWMETERS + COMP. EUROCONE EASY-CONNECTORS + SPLIT SYSTEM / DOUBLE HEAT EXCHANGER PACK + 5.5 KVS THERM. VALVES

Conform cu EMCS

.RFA

Distribuitoare - Termice

Therminon

Descărcare
Therminon Composite unit model OEM LTV 3 pipes connection

Composite unit model OEM LTV 3 pipes connection

1-16-GROUP OEM LTV / FLOWMETERS + COMP. EUROCONE EASY-CONNECTORS + SET 3-PIPE CONN. 3/4'' + 3 X 5.5 KVS THERM. VALVES

Therminon

Composite unit model OEM LTV 3 pipes connection

1-16-GROUP OEM LTV / FLOWMETERS + COMP. EUROCONE EASY-CONNECTORS + SET 3-PIPE CONN. 3/4'' + 3 X 5.5 KVS THERM. VALVES

Conform cu EMCS

.RFA

Distribuitoare - Termice

Therminon

Descărcare
Therminon Composite unit model OEM Industry

Composite unit model OEM Industry

1-20-GROUP OEM INDUSTRY / FLOWMETERS + COMP. EUROCONE EASY-CONNECTORS

Therminon

Composite unit model OEM Industry

1-20-GROUP OEM INDUSTRY / FLOWMETERS + COMP. EUROCONE EASY-CONNECTORS

Conform cu EMCS

.RFA

Distribuitoare - Termice

Therminon

Descărcare
Therminon Composite unit model Industry 3 bars

Composite unit model Industry 3 bars

1-20-GROUP COMP UNIT MODEL: INDUSTRY / 3-BARS

Therminon

Composite unit model Industry 3 bars

1-20-GROUP COMP UNIT MODEL: INDUSTRY / 3-BARS

Conform cu EMCS

.RFA

Distribuitoare - Termice

Therminon

Descărcare
Therminon Composite unit model OEM LTV split system

Composite unit model OEM LTV split system

1-16GROUP OEM LTV / FLOWMETERS + COMP. EUROCONE EASY-CONNECTORS + SPLIT SYSTEM / HEAT EXCHANGER PACK

Therminon

Composite unit model OEM LTV split system

1-16GROUP OEM LTV / FLOWMETERS + COMP. EUROCONE EASY-CONNECTORS + SPLIT SYSTEM / HEAT EXCHANGER PACK

Conform cu EMCS

.RFA

Distribuitoare - Termice

Therminon

Descărcare
Therminon Composite unit model Industry 4 bars

Composite unit model Industry 4 bars

1-20-GROUP COMP UNIT MODEL: INDUSTRY / 4-BARS

Therminon

Composite unit model Industry 4 bars

1-20-GROUP COMP UNIT MODEL: INDUSTRY / 4-BARS

Conform cu EMCS

.RFA

Distribuitoare - Termice

Therminon

Descărcare
Therminon Composite unit model Industry

Composite unit model Industry

1-20-GROUP COMP UNIT MODEL: INDUSTRY

Therminon

Composite unit model Industry

1-20-GROUP COMP UNIT MODEL: INDUSTRY

Conform cu EMCS

.RFA

Distribuitoare - Termice

Therminon

Descărcare
Therminon Unit model District Heating Nuon DA PN6

Unit model District Heating Nuon DA PN6

1-12-GROUP NUON DISTRICT HEATING DOUBLE ADJUSTABLE / PN6

Therminon

Unit model District Heating Nuon DA PN6

1-12-GROUP NUON DISTRICT HEATING DOUBLE ADJUSTABLE / PN6

Conform cu EMCS

.RFA

Distribuitoare - Termice

Therminon

Descărcare
Therminon Unit model District Heating Essent DA PN6

Unit model District Heating Essent DA PN6

1-12-GROUP ESSENT DISTRICT HEATING DOUBLE ADJUSTABLE / PN6

Therminon

Unit model District Heating Essent DA PN6

1-12-GROUP ESSENT DISTRICT HEATING DOUBLE ADJUSTABLE / PN6

Conform cu EMCS

.RFA

Distribuitoare - Termice

Therminon

Descărcare
Therminon Unit model LTV compact DA split system

Unit model LTV compact DA split system

1-16-GROUP LTV COMPACT DOUBLE ADJUSTABLE + SPLIT SYSTEM / HEAT EXCHANGER PACK

Therminon

Unit model LTV compact DA split system

1-16-GROUP LTV COMPACT DOUBLE ADJUSTABLE + SPLIT SYSTEM / HEAT EXCHANGER PACK

Conform cu EMCS

.RFA

Distribuitoare - Termice

Therminon

Descărcare
Therminon Unit model LTV compact DA

Unit model LTV compact DA

1-16 GROUP LTV COMPACT DOUBLE ADJUSTABLE

Therminon

Unit model LTV compact DA

1-16 GROUP LTV COMPACT DOUBLE ADJUSTABLE

Conform cu EMCS

.RFA

Distribuitoare - Termice

Therminon

Descărcare
Therminon Unit model 5000 DA

Unit model 5000 DA

1-16-GROUP 5000 DOUBLE ADJUSTABLE

Therminon

Unit model 5000 DA

1-16-GROUP 5000 DOUBLE ADJUSTABLE

Conform cu EMCS

.RFA

Distribuitoare - Termice

Therminon

Descărcare
Therminon Composite unit model LTV split system double heat exchanger

Composite unit model LTV split system double heat exchanger

1-16-GROUP COMP UNIT MODEL: LTV + SPLIT SYSTEM / DOUBLE HEAT EXCHANGER PACK + 5.5 KVS THERM. VALVES

Therminon

Composite unit model LTV split system double heat exchanger

1-16-GROUP COMP UNIT MODEL: LTV + SPLIT SYSTEM / DOUBLE HEAT EXCHANGER PACK + 5.5 KVS THERM. VALVES

Conform cu EMCS

.RFA

Distribuitoare - Termice

Therminon

Descărcare
Therminon Composite unit model LTV split system heating/cooling

Composite unit model LTV split system heating/cooling

1-16-GROUP COMP UNIT MODEL: LTV + SPLIT SYSTEM HEAT EXCHANGER PACK 4-PIPE / 5.5 KVS THERM. VALVES / COOLING VALVE NC

Therminon

Composite unit model LTV split system heating/cooling

1-16-GROUP COMP UNIT MODEL: LTV + SPLIT SYSTEM HEAT EXCHANGER PACK 4-PIPE / 5.5 KVS THERM. VALVES / COOLING VALVE NC

Conform cu EMCS

.RFA

Distribuitoare - Termice

Therminon

Descărcare
Therminon Composite unit model LTV 3 pipes connection

Composite unit model LTV 3 pipes connection

1-16-GROUP COMP UNIT MODEL: LTV + SET 3-PIPE CONN. 3/4''+ 3 X 5.5 KVS THERM. VALVES

Therminon

Composite unit model LTV 3 pipes connection

1-16-GROUP COMP UNIT MODEL: LTV + SET 3-PIPE CONN. 3/4''+ 3 X 5.5 KVS THERM. VALVES

Conform cu EMCS

.RFA

Distribuitoare - Termice

Therminon

Descărcare
Therminon Composite unit model LTV split system

Composite unit model LTV split system

1-16-GROUP COMP UNIT MODEL: LTV + SPLIT SYSTEM / HEAT EXCHANGER PACK

Therminon

Composite unit model LTV split system

1-16-GROUP COMP UNIT MODEL: LTV + SPLIT SYSTEM / HEAT EXCHANGER PACK

Conform cu EMCS

.RFA

Distribuitoare - Termice

Therminon

Descărcare
Therminon Composite unit model LTV 4 pipe connection

Composite unit model LTV 4 pipe connection

1-GROUP COMP UNIT MODEL: LTV + SET 4-PIPE CONN. 3/4'' + 4 X 5.5 KVS THERM. VALVES

Therminon

Composite unit model LTV 4 pipe connection

1-GROUP COMP UNIT MODEL: LTV + SET 4-PIPE CONN. 3/4'' + 4 X 5.5 KVS THERM. VALVES

Conform cu EMCS

.RFA

Distribuitoare - Termice

Therminon

Descărcare
Therminon Composite unit model OEM LTV

Composite unit model OEM LTV

1-16-GROUP OEM LTV / FLOWMETERS + COMP. EUROCONE EASY-CONNECTORS

Therminon

Composite unit model OEM LTV

1-16-GROUP OEM LTV / FLOWMETERS + COMP. EUROCONE EASY-CONNECTORS

Conform cu EMCS

.RFA

Distribuitoare - Termice

Therminon

Descărcare
Therminon Composite unit model LTV

Composite unit model LTV

1-16-GROUP COMPOSITE UNIT MODEL: LTV

Therminon

Composite unit model LTV

1-16-GROUP COMPOSITE UNIT MODEL: LTV

Conform cu EMCS

.RFA

Distribuitoare - Termice

Therminon

Descărcare
Mitsubishi Electric City Multi HBC Controllers (HVRF)

City Multi HBC Controllers (HVRF)

Slave HBC controllers Place directly in Revit and AutoCAD using the free [a href="https://store.mepcontent.com/Product/Details/49" target="_blank"]Mitsubishi Electric System Designer[/a] App

Mitsubishi Electric

City Multi HBC Controllers (HVRF)

Slave HBC controllers Place directly in Revit and AutoCAD using the free [a href="https://store.mepcontent.com/Product/Details/49" target="_blank"]Mitsubishi Electric System Designer[/a] App

Conform cu EMCS

.DWG .RFA .IFC

Distribuitoare - Termice

Mitsubishi Electric

Descărcare
Mitsubishi Electric City Multi BC Controllers

City Multi BC Controllers

BC controllers Place directly in Revit and AutoCAD using the free [a href="https://store.mepcontent.com/Product/Details/49" target="_blank"]Mitsubishi Electric System Designer[/a] App

Mitsubishi Electric

City Multi BC Controllers

BC controllers Place directly in Revit and AutoCAD using the free [a href="https://store.mepcontent.com/Product/Details/49" target="_blank"]Mitsubishi Electric System Designer[/a] App

Conform cu EMCS

.DWG .RFA .IFC

Distribuitoare - Termice

Mitsubishi Electric

Descărcare
Giacomini R551

R551

Distribuitor multiplu

Giacomini

R551

Distribuitor multiplu

Conform cu EMCS

.DWG .RFA

Distribuitoare - Termice

Giacomini

Descărcare